I’m working on a project which requires me to use an oscilloscope. I have never had a need for such a device, so I was very surprised when I priced used oscilloscopes used at €300.

As a result, I looked at my options and I was happy to find there are a plethora of known as USB Oscilloscopes. These are hobby-level oscilloscopes, which are less expensive because they save money on the computing and display components of the device.

This oscilloscope in particular, is quite capable. At about $70,  my Sain Smart DDS-120, included the scope, two channels, two probes, a logic analyzer and an external trigger.  You can find the specs of the scope here.

Anyway, given I only have a Apple computers and the software for the scope runs on windows I thought I would share what I did to make it work.


At this point, it should be fair to assume you have access to the scope and you just need to get it working. There are two options for getting Windows to run on your Mac computer, you can go dual-boot (the reliable and least convenient), or Virtual Machine (less reliable, though not unreliable, and most convenient). I chose the latter. There are a bunch of Virtual Machine options, I chose VirtualBox, or VBox. I chose VBox because it’s free and it works pretty well. With that in mind, here are the steps I followed to get the scope working on MacOS.

  1. Download and install the latest version of VirtualBox. I used version 5.2.x
    1. On MacOS 10.13, I got an error message at the end of the installation saying I needed to allow the program to run in security & privacy preferences pane. After I did this, the installation said there was an error and it had not installed correctly. I simply re-installed it, and the installation completed without any issues (not even the security & privacy warning).
  2. Download and install the latest VirtualBox Oracle VM VirtualBox Extension Pack. This will be in the VirtualBox download page and cannot be installed until AFTER you have installed VirtualBox. To install just double-click on the file and it will automatically pickup VirtualBox and install itself there.
  3. Once installed, you need to create a Win7 Virtual Machine (VM). To do this:
    1. Click on “New”
    2. Click “Create”
    3. Click “Create” again and you are done
  4. At this point you have an empty VM. You will need a Win7.iso file. These are easy enough to find on the internet. If you need one, message me directly and I can point you in the right direction. Assuming you have an ISO image, select the VM and click on Start –> Normal Start. Since you need to load the OS into the VM, you will get this error message (though instead of Windows 7 Ultimate… yours will likely say “Empty”. Click on the Folder Icon next to the drop-down and select the your Win7.iso file. Click start and follow the instructions.
  5. After you have finished installing Win7 you will need to setup Scope software and calibrate the probes.
    1. Enable the scope’s USB to connect through your Mac onto the VM by following these steps:
      1. Start the VM
      2. Connect the Scope to the Mac using the USB cable
        1. Your Mac should NOT pick up the scope as it’s not compatible, so don’t worry if nothing happens on your Mac (the host)
      3. Right-click on the VM and choose settings. Under settings click on “Add Filter” and select BUUDAI USBxxx. Make sure to select it and click OK.
      4. The VM will inform you that it’s installing the necessary drives and it should just begin picking it up going forward.
    2. Install the software. The software I used is here: Software_V1.5.0. The zip file includes everything I needed to get it to work. Just look for DDS120.exe inside the folder and that’s it 🙂
      1. You can check installation by clicking on “Start” on the bottom right of the software screen.
    3. Now you need to calibrate the probes.
      1. To calibrate the probes, set them to 10X and connect them to the scope and use the signal emitter between the two channels to calibrate them. 2018-01-25 18.00.44.jpg
      2. Inside the Scope software do the following:
        1. Select Channel 1 and make sure it’s On and set to 10X
        2. Set the time to 1ms
        3. Set Channel 1 Voltage to 50mV
        4. Optionally, you can zoom in to get a closer look at the waves (but this is not necessary
      3. You want the signal to be as square as possible. You can adjust it by using a small screwdriver to calibrate the wave shape. The probes are pretty good, but not perfect. So don’t worry if you cannot get the shape of the wave to be perfectly square.

That’s it you are done and ready to begin using your new USB scope.

Leave a Reply

Your email address will not be published. Required fields are marked *